Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window doctor (www.repairmywindowsanddoors.co.uk) or door mechanism not working properly? Perhaps the window or door handles aren't aligned properly or are difficult to use.

You'll lose energy in the event that your double-glazed doors fail to perform as they should. This can also increase the chance of burglary. Owen the Locksmith can repair your door lock for an affordable price.

Snapped Key

It can be frustrating when a key gets stuck inside a lock. It could also be a security risk in that it can expose you to an intruder if the door does not lock. There are a few easy fixes you can make to repair the issue and make your door functional again.

Remember to remain calm. If you get scared and start playing around with your keys you may end up pushing the damaged piece of the key deeper into the lock, thereby making the situation worse.

Next spray WD-40 or another penetrating oil into the lock to help the broken piece to slide out more easily. You can also use a screwdriver to help break up any pieces stuck that might be hindering the flow. If you're fortunate enough to have a bit of the key left visible, you can make use of a paperclip or other metal object that is thin to grab it and then pull it out. Both methods are effective, but you need to be careful not to push the damaged key piece further into the keyway.

Some paperclips have grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you don't happen to have any of these you can bend a hook with needle-nosed pliers. Additionally, a pair of tweezers is a good way to grasp and pull out the last part of the broken key.

If you are unable to remove the broken key piece, use a lock deicer. It is available in most hardware stores and is used to freeze any moisture present within the lock.

If none of these methods appear to be working then it's probably time to call in locksmith. Fitlocks specialists are able to quickly solve problems with uPVC door mechanisms and locks that have snapped keys as well as broken handles. They can also alter the double glazing door mechanisms so that they are simpler to operate. Book a double glazing repair with us online, or give us a phone call to discuss your requirements.

Broken Cylinder

A damaged cylinder poses a serious security threat. A locksmith professional can repair the cylinder. To repair the cylinder, locksmiths must tap it. They can do this with a hammer or other tool, but the most efficient way is to use a long match or a piece of wire. Place the match or wire's end in the keyway. The locksmith can then hit the lock to crack it. This is much better than using a heavy hammer that can damage the lock.

The most common cause of cracks in the cylinder head is overheating. This can occur when the block and the cylinder head are made from different metals such as cast-iron and aluminium. Different metals can heat up and cool off at different rates. This can cause localised hotspots to expand faster than the rest of the cylinder.

Corrosion can be a reason for fractures in cylinders. If the cylinder head as well as cylinder block are not maintained properly, this could cause corrosion or rust that could cause them to expand at a greater rates than they should. This could lead to cracks in the future.

If your uPVC window or door lock is brittle and requires a lot more pressure to turn, it could be due to a variety of reasons. This can be caused by a faulty locking mechanism, or misalignment as well as a worn-out handle.

Fortunately, this is an easy and affordable fix for the majority of homeowners with double glazing. A professional locksmith will usually be able to resolve the issue within an hour of arriving at your property. Depending on your needs they can change the locking mechanism, change the window handles, and also change the gearboxes. A professional locksmith will be able to advise you on the most cost-effective solutions for your home. They can even recommend upgrades to high-security 3 Star Euro cylinders, TS007, that will add an extra layer of protection against burglars. This is a small price to pay for the peace of mind that comes with knowing your uPVC doors are safe.

Broken Handle

Window handle locks have intricate mechanisms that deteriorate as time passes and use, so it's not a surprise that they can break. It can be difficult to determine the cause of the broken window handle lock and then fix it properly.

Whether the problem is with the internal locking mechanism or the latch, fixing the broken handle can improve your uPVC double glazing door's security as well as help you stop draughts. It is costly to repair or replace your handle incorrectly and it can also harm the frame and lock of your door.

Screwdriver Open the window replacement, loosen the screw holding the handle. The screw should be on the inside face of the back plate, normally covered by an attractive cover for the screw for aesthetic reasons. Be careful not to lose any internal components within the handle, such as the plates or levers on the opposite side of the spindle. Ideally, keep these in the same place so you can replace them again if needed.

Then, with another screwdriver, loosen the screw that connects the handle with the spindle in the back. Once the screw is free, you can take the handle off and take the broken spindle out. Replace it with a brand new spindle, ensuring that it's the same length (you can buy them on the internet or at hardware stores). Securely screw it into the frame. Do not tighten the screw too much as this can harm the handle as well as the window frame.

Close the handle and try it. The hope is that it will function smoothly and you'll be able to open your window again.

While you're working on the handle, don't forget to check your uPVC windows are shut properly. If they don't cause damp and draughts in your home, as in addition to compromising your home's energy efficiency. Core Sash Windows is a local window company that can adjust the hinges on your window frames to ensure that they close properly.

Broken Spindle

It is more common for the spindle to break than the handle. This is especially typical in uPVC tilt and turn windows. These windows require a handle that operates an locking device within the window frame. The handle is connected to a rod in the centre that in turn activates cams that resemble mushrooms, which secure the frame of the window. If the dead latch mechanism fails to open when the handle has been turned, Window Doctor it's likely the spindle is broken. This could be a frustrating problem.

Luckily, there are steps that can be taken to fix this problem. A skilled locksmith can quickly and efficiently fix this problem. They will be able to remove the window handle using a tool that removes the wheel portion of the mechanism that is where the spindle is. This can be done without damage to the handle or window frame.

Once the wheel has been removed, the technician can inspect the spindle to determine what caused it to break. This involves disassembling the spindle and inspecting each component, noting any damage or excessive wear. This procedure is usually performed in a clean room by skilled technicians.

Next, clean the damaged spindle. This will help get rid of any debris or dirt that could be hindering it from functioning normally. Following this the spindle is cleaned, it can be repaired or replaced. If the technician is replacing the spindle, it is possible to use a dowel that is comparable in size to the original. The technician will then drill matching holes into both pieces. This will ensure that the spindle is perfectly matched with the handle.

If the damaged spindle cannot be repaired it may require replacement. Home centres sell generic substitutes but if the window design is unusual then you'll require contacting an expert in cabinet making or woodworking who can replicate the exact piece. Once the new spindle is installed, it can be attached to the handle by lining up the screw holes in the handle and the frame existing screws. Once the new handle is firmly installed, you are now ready to operate your uPVC window.