Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window or door mechanism broken? Perhaps the handles on your uPVC windows or repairmywindowsanddoors doors aren't aligned correctly or are difficult to use.

You'll be wasting energy in the event that your double-glazed doors fail to work properly. This also increases the risk of burglary. Owen the Locksmith can fix your door lock for an affordable cost.

Snapped Key

If a key breaks inside a lock, it could be incredibly annoying. It could also be a security risk since the door may not lock and leave you open to intrusion. There are a couple of quick solutions you can use to repair the issue and get your door working again.

First, remember to stay calm. If you panic you may end up pushing the broken key piece further into the lock.

Spray WD-40, or any other penetrating lubricant into the lock. This will allow the broken piece emerge more easily. You can also use the screwdriver to break off any pieces stuck. If you're lucky enough to have a bit of the key left hanging out and you want to remove it, make use of a paperclip, or any other metal object that is thin to grab it and remove it. Both of these methods work well, but be careful not to push the damaged piece of the key deeper into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades also work well for this. If you don't happen to have one of these tools you can bend a hook using needle-nosed pliers. Finally, you can use a pair of tweezers grab and pull out the remaining pieces of broken keys.

If you're unable to pull the broken piece of the key out, try using a lock de-icer. This is usually available at all hardware stores. It is used to freeze any moisture or ice that may be in the lock.

If none of these strategies seem to be helping you, it's time to call locksmith. Fitlocks specialists are able to quickly solve problems with uPVC door locks and mechanisms that have snapped keys as well as broken handles. They can also reconfigure double glazing door mechanisms so that they are more easy to use. You can book an appointment online for a double-glazing repair or contact us to discuss your requirements.

Broken Cylinder

A broken cylinder is a serious security threat. It's fortunately a simple repair for a professional locksmith to complete. To fix the cylinder, locksmiths will need to tap it. They can do this with an hammer or another tool, but the best method is to use an extended match or piece of wire. Then, put the match's end or wire in the keyway. The locksmith will hit the lock to break it open. This is superior to using the hammer, which could cause damage to the lock.

The most frequent cause for cracks in the cylinder head is overheating. This can occur when the cylinder block and head are made of various metals, such as cast iron and aluminium. Different metals will heat up and cool off at different rates. This can cause localised hotspots to expand quicker than the rest of the cylinder.

Another possible cause for cracks in cylinders is corrosion. If the cylinder block and head are not maintained correctly, they can corrosion or rust and cause them to expand faster than expected. In time, this could also cause cracks.

If your uPVC window lock or door is stiff or requires a lot of pressure to turn, this can be the result of a number of things. A defective locking mechanism, misalignment or a worn handle are common causes of this issue.

This is a simple and inexpensive fix that most homeowners with double glazing can perform. A professional locksmith will usually solve this issue within an hour of arriving at your property. They can replace the locking mechanisms, or replace the window handles and change the gearboxes, based on the specific requirements of your home. A professional locksmith can always advise you on the most cost-effective solution for your home. They can recommend upgrading to 3 Star TS007 Euro Cylinders which provide an additional layer of protection from burglars. It's a small price to enjoy the peace of mind that comes from knowing that your uPVC door is secure.

Broken Handle

Window handle locks have intricate mechanisms that wear out with time and usage, so it's no surprise that they sometimes break. If yours fails, it can be difficult to determine the source of the problem and make sure that you repair it correctly.

Fixing the broken handle, whether it's the internal locking mechanism or latch can increase the security of your uPVC door and stop draughts. When you aren't doing it right, replacing or repairing your handle can be expensive and can harm the door's frame as well as lock It is therefore worth taking the time to do it right.

Screwdriver When the window is open remove the screw that holds the handle. It should be located on the inside face of the back plate, normally hidden by an attractive cover for the screw for aesthetic reasons. It is not recommended to be able to replace any internal parts of the handle like the plates and levers on either side. Keep them in the same arrangement to make it simpler to replace them in the event of a need.

Then, with another screwdriver take the screw off that connects the handle to the spindle at the back. Once the screw is loose, you can remove the handle and take out the broken spindle. Replace it with a new spindle, ensuring that it's the same length (you can find them online or in hardware stores). Screw it into the frame. Don't over tighten the screw as this could harm the handle as well as the window frame.

Check that the new handle is correctly installed, then close and test the handle. It should work smoothly and you'll be able open your window once more.

While you're working on the handle, be sure to make sure your uPVC windows are closing properly. If they're not then you may experience damp and draughts in your home, as well as compromising the efficiency of your home's energy usage. Core Sash Windows is a local window doctor company that can alter the hinges on the frames of your windows to ensure that they shut correctly.

Broken Spindle

It is often the case that the spindle inside the handle breaks, RepairMyWindowsAndDoors rather than the handle itself. This is particularly frequent in uPVC tilt and turn windows. These windows require a handle that acts as a locking device in the window frame. The handle is attached a central rod that triggers the mushroom-shaped locking cams that secure into the frame of the window keep. If the dead latch mechanism does not open when the handle is turned it is possible that the spindle has broken and this could be a very frustrating issue.

Luckily there are steps that can be taken to rectify this issue. A skilled locksmith can quickly and effectively fix the issue. A professional locksmith will be able disassemble the handle of the window by using a tool to remove the wheel from the area that houses the spindle. This is done without damaging the handle or causing any other damage to the frame of the window.

After the wheel has been removed, the technician can inspect the spindle to determine what caused it to break. This involves breaking the spindle into its individual components and carefully observing their general condition, as well as any specific areas of wear or damage. The process is performed in a clean room by highly skilled technicians.

The next step is to clean the damaged spindle. This helps eliminate any debris or dirt that might be hindering its normal function. The spindle may be repaired or replaced. If the technician is replacing the spindle, it is possible to use a dowel that is comparable in size to the original. He will then make holes in the same way into both pieces. This will ensure that the spindle fits perfectly with the handle.

If the damaged spindle cannot be repaired, it could require replacement. Home centers sell generic replacements. However, if the style of your window is unusual then you will need to contact a wood worker or cabinet maker who can duplicate the exact component for you. Once the new spindle has been installed it can be fitted to the handle by lining up the screw holes in the handle and the frame existing screws. Once the new handle is firmly installed, you are now ready to operate your uPVC window.