Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they do not corrosion or rot.

It is essential to clean and oil UPVC doors and windows on a regular basis. This will reduce unnecessary repair costs and also increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause serious damage to your home and even be fatal. It is crucial to take the time to make sure that you're doing everything you can to ensure that your windows are in good repair.

For single pane windows, it is fairly easy to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. If you have double-paned windows that are held together by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this situation it is essential to purchase plastic spacers in order to aid in fitting the new pane into the window frame.

If you're planning to try to remove the window repairs near me panes yourself it is important to wear the appropriate safety equipment, including thick gloves and protective eyewear. You should also lay down a dropcloth before you begin working on the window panes so that any shards fall onto the fabric and not onto the floor and could be trampled.

Once the glass has been removed from the window, it's best to seal the gap with packaging tape or duct tape to prevent water and drafts from entering the home until a professional can come out and repair the window. It also acts as a barrier, deterring any intruders to gain access to your home. If the distance between the door and the window is significant, you may want to use a security screen that also includes a window. This will give you the best of both.

2. Sagging

Upvc windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. However, double glazing repairs near me with time, they are susceptible to a range of issues like sagging. A window that is sagging can cause problems with light, draughts, and even security. It's crucial to act when you discover that your uPVC windows are sliding.

To fix a sagging window you can try to reposition the hinges. You'll first need to open the windows so you can access the frame. Then, you can remove the hinges at the top and bottom with a screwdriver and adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and verify the an appropriate fit. If you're satisfied with the fit of the window, tighten the screws to hold them in the right position.

If you are unable to reposition the hinges you may need to replace the seal. Over time, rubber seals lose their elasticity and dry out, which causes them to lose tightness. If this happens, it's essential to replace the seal as fast as possible to ensure your uPVC windows are watertight and draught-proof.

uPVC handles may also become loose. Often it is due to screws that have become loose over time. However, it can occur because the handle mechanism has been worn out. Fortunately, it's easy to repair a loose uPVC window handle yourself. The first step is to close the window and then perform a test to ensure that it fits. The corners of the sash should be aligned with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle and reverse the mechanism back into the position it was in.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains it's crucial to take action. Leaks of water from windows can cause structural damage to your home, and hinder your ability to control the temperature of your home. The most common cause for leaking uPVC windows is that the sealant around the frame has been damaged or is missing.

This is an easy fix that can be done by any DIYer who has the ability. Based on the severity of the issue the old caulking might need to be removed before a new layer of caulk can be put on. It is crucial to remember that when it is about uPVC window repairs, do not be tempted to apply too much caulk in order to make the area harder to clean and can decrease the efficiency of your energy usage.

Check that any drainage holes do not have debris inside them and that the sill pan is properly angled to drain away from the window. In more serious instances, you might have to consider replacing the window.

Other indicators of long-term water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to note that if the leakage originates from the glass of your double glazing repairs glazed windows, it is more likely to be an issue with the glass seal, rather than the frame or Repairs sliding. Again this can easily be fixed by an uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for cheap the reason that your uPVC window is difficult to open or it opens with a breeze. Any competent DIYer can replace these in a matter of minutes.

Like any mechanical component hinges will wear out over time. It is very easy to change the hinges on a window however it is easier if someone helps you hold the frame.

Check that the uPVC hinges are closed and open in the right direction. Look for the arrows on each hinge to determine which way the window should be opened.

The issue can be caused either by opening the window incorrectly or a faulty installation at the factory. Sending us a photo through our website can often solve the issue. We are more than happy to provide advice.

Regularly lubricating the hinges is also necessary. Applying a light engineering lubricant on the hinges is a great method to accomplish this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window to operate and close more easily. It can also reduce the risk of a window sticking and prevent corrosion. This is recommended to be done at least every year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different things. The hinges can also be unbalanced due to wear, which can cause a gap between the frame and sash. If they're beyond repair, it could be necessary to get them re-aligned. Secondly the interlock, this is located on the hinge side of the window and can be misaligned. Again, it's possible to give them a clean but in some cases it might be necessary to get them replaced.

These seals are susceptible to wear and tear or be damaged over time, allowing air to escape. Replacing these with high-quality weatherstripping is a good way to prevent draughts. Replace the windows made of upvc with low-emissivity glass. This will help regulate indoor temperatures, and reduce the possibility of draughts.

Another method of reducing the amount of draughts is to use a Draught-excluder. These are usually fabric tubes filled with a filler which can be placed over your window sill. These will keep your home warm by blocking out cold air.

With a little regular maintenance and repairs, your upvc windows will continue to provide excellent security and insulation for your home. It is essential to remember that all windows eventually get worn out and it may be cheaper to replace them than to repair them. So, if you are experiencing issues with your Upvc windows, it is recommended to seek assistance from a professional as soon as you can.