Double Glazing Door Lock Repairs

Is your upvc window repairs window or door mechanism faulty? Perhaps the handles on your uPVC windows or doors aren't aligned properly or are difficult to operate.

It's important that your double glazed doors operate smoothly, otherwise you'll lose energy and increase the chances of burglary. Owen the Locksmith can fix your door lock for an affordable price.

Snapped Key

It can be frustrating when a key snaps inside a lock. It's also potentially an issue for security, since the door may not lock and could leave you open to intrusion. There are a few easy solutions you can use to fix the problem and make your door functional again.

Remember to remain calm. If you get scared and start poking around wildly you may end up pushing the broken piece of the key further into the lock, making the situation worse.

Next spray WD-40 or a different penetrating oil into the lock to make the broken piece slip out more easily. You can also employ a screwdriver in order to break up any pieces stuck that could be hindering the flow. If you happen to have a small piece of the key that is visible it, you can make use of a paperclip, or any other thin metal object to grab it and then pull it out. Both methods work well, but be very careful not to push the broken piece of the key further into the keyway.

Some paperclips have grooved edges that could work in a pinch as hook extractors and Jigsaw blades also work for this purpose. If you don't have any of them handy, you can use needle-nose pliers to bend them and create hooks. You can also make use of a pair of tweezers to grab and pull out the last piece of broken keys.

If you cannot remove the broken key piece, use a lock deicer. It is available in most hardware stores and works by freezing any moisture that may be present in the lock.

If none of these solutions work, window Doctor it may be time to contact a locksmith. Fitlocks experts can solve problems like broken handles and snapped keys using upvc window repairs locks and door mechanisms. They can also alter your double glazing door mechanisms to allow them to operate more easily. You can request repairs to your double-glazing online or call us to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a major security risk. A locksmith professional can repair the cylinder. To fix the cylinder, a locksmith will need to tap it. They can do this with a hammer or other tool, but the best method is to make use of a long match or a piece of wire. Then, place the match's tip or wire close to the keyway. The locksmith can then hit the lock to crack it. This is more secure than using a hammer, which can cause damage to the lock.

Overheating is the most common reason behind cylinder heads cracking. This can happen when the block and the cylinder head are made of various metals such as cast-iron and aluminum. Different metals can heat up and cool down at different rates. This can cause localized hotspots to expand quicker than the rest of the cylinder.

Another possible cause of cracks in cylinders is corrosion. When the cylinder head and the block of the cylinder are not properly maintained, this can cause corrosion or rust that could cause them to expand at a greater rates than they ought to. In time, this could cause cracks.

If your uPVC window or door lock is stiff or requires an enormous amount of pressure to turn, this could be due to a number of things. A faulty locking mechanism, misalignment, or an old handle are the most common causes of this problem.

This is a simple and inexpensive fix that most double glazing owners can accomplish. A professional locksmith will usually fix this problem within one hour of arriving at your home. Based on your requirements, they can replace the locking mechanism, replace the window handles, and change the gearboxes. A professional locksmith will be able to provide you with a recommendation of the most cost-effective option for your home. They can also suggest upgrades to high-security 3 Star Euro cylinders, TS007, that will provide an extra layer of security against burglars. It's a small amount to get the peace of mind that comes from knowing that your uPVC door is secured.

Broken Handle

It's not a surprise that window handle locks could break. They have intricate mechanisms which deteriorate over time. It isn't always easy to pinpoint the reason for the broken window handle lock and repair it correctly.

Fixing your broken handle, whether it's the internal locking mechanism or latch can increase the security of your uPVC door and stop draughts. It could be costly to repair or replace your handle incorrectly and it can also harm the frame and lock of your door.

Screwdriver: With the window open remove the screw that holds the handle. It should be located on the inside of the back plate, and is normally covered by an attractive cover for the screw for aesthetic reasons. Be sure not to lose any of the internal components within the handle, like the plates or window doctor levers on the opposite side of the spindle. Keep them in the same order so that it is simpler to replace them in the event of a need.

Then, using an additional screwdriver loosen the screw that connects the handle to the spindle at the back. Once the screw is free, you can take the handle off and take the broken spindle out. Replace it with a brand new one, making sure that it's the same size as the old one (you can typically find these on the internet or at hardware stores) and then securely screw it into place. Be careful not to tighten too much because this could cause damage to the handle or the window frame.

Make sure the new handle is correctly installed Close the window and test the handle. It is likely that it will operate smoothly and you'll be able unlock your window.

Don't forget to double-check that your uPVC window is shut properly while you're working with the handle. If they don't close properly, you may experience damp or draughts in your home. It could also affect the energy efficiency of your home. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your Window Doctor frames so they can shut properly.

Broken Spindle

It is often the case that the spindle in the handle breaks, rather than the handle itself. This is particularly frequent in uPVC tilt and turn windows. These windows require a handle to operate an electronic locking mechanism within the frame of the window. The handle is attached to a centre rod that triggers a set of mushroom-like locking cams, these locks are inserted into the window frame. If the dead latch mechanism does not open when the handle is turned it is likely that the spindle is broken and this could be a frustrating problem.

There are ways to fix this issue. A good locksmith can quickly and effectively address this issue. They will be able to remove the window handle using a tool that removes the wheel portion of the mechanism that is where the spindle goes. This can be done without causing any damage to the handle or causing any other damage to the window frame.

After removing the wheel the technician will inspect the spindle and determine what caused it to break. This involves breaking the spindle into its individual parts and meticulously noting their general condition, as in addition to any specific areas of damage or excessive wear. This process is typically carried out in a clean, well-lit room by skilled technicians.

The next step is to clean the damaged spindle. This assists in removing any dirt or other debris that might be obstructing its normal function. Following this the spindle could be repaired or replaced. If it is being replaced the technician will need a dowel of a similar size to the original and drill mating holes in both pieces of the spindle. This ensures that the new spindle is precisely matched to the handle.

If the damaged spindle is beyond repair, it could be necessary to replace it completely. Home centers can sell generic replacements however if your window design is unique, you will have to speak with an expert in woodworking or cabinet making who can replicate the exact piece. Once the new spindle is in place it can be attached to the handle by line up the holes for screws in the handle with the frame's existing screws. Once the handle is seated, you can operate your uPVC windows.